The TPW4052 is a dual SP4T analog switch suitable for use in analog or digital multiplexer/demultiplexer applications. The switch features three digital select inputs (S0, S1), eight independent inputs/outputs (An, Bn), two common input/output (A, B), and a digital enable input (/E). When /E is HIGH, the switches are turned off.

The TPT3232E is IEC61000 ESD protected, 3.0V to 5.5V powered transceivers that meet the RS-232 standards for balanced communication. Each receiver converts TIA/RS-232 inputs to TTL/CMOS levels.

The TPT1042 is a CAN transceiver that meets the ISO11898 high-speed CAN (Controller Area Network) physical layer standard. The device is designed to be used in CAN FD networks up to 5 Mbps, with enhanced timing margin and higher data rates in long and highly loaded networks. As designed, the device features crosswire, overvoltage, and loss of ground protection from −70 V to +70 V, over-temperature shutdown, with a −30 V to +30 V common-mode input voltage range.

The TPT9H111 is a 3.3V Multipoint-Low-Voltage Differential (M-LVDS) line driver and receiver, which can support 100 Mbps data rates. Driver outputs and receiver inputs are protected against ±8kV ESD strikes without latch-up. The driver output has been designed to support multipoint buses with the loads no less than 30 Ω, and can support the controlled slew rate on drivers.

The TPD160221 is a dual differential channel 2:1 multiplexer/demultiplexer switch for PCIe Gen3.0, Gen4.0, DP1.3, DP1.4, USB3.1, USB3.2, or other high-speed serial interface signals.

The TPT29545 is a 1:4 bidirectional translating I2C switch. The SCL/SDA upstream pair fans out to four downstream channels. Any single SCn/SDn channel or combination of channels can be selected, determined by the programmable control register. Four interrupt inputs (INT0 to INT3) are designed as one for each of the downstream pairs. One interrupt (INT) output acts as an AND of the four interrupt inputs.

The TPT24857 is an SD 3.0 spec-compliant memory card voltage-level translator with bidirectional control. It is designed to translate voltage between voltage 1.8 V to 3.0 V in the card side and 1.2 V to 1.8 V in the host side.

The BL8573 is a single cell, fully integrated constant current (CC)/constant voltage (CV) Li-ion battery charger. Its compact package with minimum external components requirement makes the BL8573 ideal for portable applications.

The TPB4056A is a cost-effective, high-integration linear charger for single-cell Li-ion or Li-ion polymer batteries. The device supports CC/CV charge from either a USB port or an AC adapter. The low BOM component requirement makes the whole system small in size. The high input voltage range with over-voltage protection supports lowcost unregulated adapters.

The TPB7462 series is a secondary overcharge hardware protector for 2s, 3s, or 4s lithium-ion battery packs.

The TPB76200 device is a high-side NFET driver integrated with a charge pump for a 48-V battery pack. It improves the safety of the battery pack by disconnecting the charging or discharging path at the battery-positive terminator. It avoids high-voltage broking communication ports by continuous ground. The device has a pre-charge or pre-discharge FET control. It can be used as a precharge FET control to charge a depleted battery and to slow the inrush current when a large bulk capacitor load is connected to the battery pack.

The TPB76200 device is a high-side NFET driver integrated with a charge pump for a 48-V battery pack. It improves the safety of the battery pack by disconnecting the charging or discharging path at the battery-positive terminator. It avoids high-voltage broking communication ports by continuous ground. The device has a pre-charge or pre-discharge FET control. It can be used as a precharge FET control to charge a depleted battery and to slow the inrush current when a large bulk capacitor load is connected to the battery pack